Insteon 2852-222 Water Leak Sensor

Insteon 2852-222 Wireless Water Leak Sensor

Usually ships within 24 hours

Need Some Advice? Speak to one of our staff

INSTEON Leak Sensor is a wireless floor-mounted sensor that instantly alerts you via another INSTEON device when it detects moisture. Place it near toilets, water heaters, washers and other home appliances to stop water damage before it happens.

The risk of water damage in a home is high. In fact, it is one of the most common home insurance claims. Every year millions of homeowners suffer billions of dollars in losses. But these losses can be reduced or even avoided altogether with the new INSTEON Leak Sensor. Leak Sensor alerts you so you can stop the leak before damage to your home occurs. Add the sensor to an INSTEON computer controller such as HouseLinc and configure the software to email or send text messages upon an alert from the sensor. Fully automate it! You can manually link the sensor (or via software, use a macro) to control a whole-house shutoff valve so it can automatically turn off all water to your home. You could even flash lights. This easy to use, battery powered leak sensor can provide the early detection necessary to prevent leaks from creating major damage to your home.

The INSTEON Leak Sensor installs quickly and easily - no need to run wires or drill holes. Simply place the sensor near where water leaks may occur. Some common places are:

  • Washing machines
  • Toilets
  • Water heaters
  • Sinks
  • Refrigerators (water filters)
  • Dishwashers
  • Basements
  • Water Softeners

Simple Design
Other leak sensors on the market require running wires or drilling holes, the INSTEON Leak Sensor is an all-in-one design. This makes it super simple to install and ideal for placing in tight areas.

Long Lasting Battery Life
A lithium battery comes included with the INSTEON Leak Sensor and will provide over 10 years of operation. To add a level of security, the sensor also features a "heartbeat" signal which is sent daily. This can be used by central controllers and/or cloud services to notify you that the sensor is still functioning or in the absence of the signal that there is a problem.

Start with one, grow to dozens if you wish. INSTEON also offers motion and open/close (door/window) sensors.

Never again leave home without knowing that your possessions and loved ones are safe. The INSTEON Smoke Bridge monitors First Alert® ONELINK® smoke and carbon monoxide detectors, allowing you to create email and text message alerts that can be sent to you no matter where you are.

Monitor the state of your home and be alerted to smoke, fire and carbon monoxide. When paired with an INSTEON Hub, the Smoke Bridge can send alerts to your smartphone via text or email informing you that something is wrong and giving you the knowledge to act to save your home and family from potential disaster.

• Works with First Alert ONELINK smoke and carbon monoxide detectors
• Enables alerts via text message and email when paired with the INSTEON Hub, ISY994i Controller, HouseLinc software, or other compatible central controller
• Only one Smoke Bridge needed to for an entire house of ONELINK Smoke Detectors
• Receive specific notification in case of smoke, carbon monoxide, low battery, all clear, or error messages with HouseLinc
• Can be linked to lights or other INSTEON devices manually or via software to turn lights on instantly in the event of an alert



Manufacturer product no. 2852-222, INSTEON Leak Sensor
UPC 813922013078
Warranty 2 years, limited
INSTEON powerline mesh repeater No
INSTEON RF mesh repeater No
INSTEON controller Yes
INSTEON responder No
Maximum links/scenes 400
Commands supported as responder On Group 1 (Dry) On Group 2 (Wet)
Heartbeat (Group 4)
Software configurable Yes
RF range Up to 150 feet (open air)
Phase bridge detect beacon No
INSTEON device category 0x10
INSTEON device subcategory 0x08 (915MHz RF frequency)
Mounting Place on flat surface where leak will occur
Case color White
Buttons 1, Set
Plastic Polycarbonate
Rubber Polyethylene rubber
Conductive Feet Corrosion resistant nickel plated bronze
Beeper No
Setup LED Yes, green

Excluding antenna: 0.9" H x 3.6" W x 1.4 D (23mm H x 92mm W x 36mm D)

With antenna: 3.7" H x 3.6" W x 1.4" D (93mm H x 92mm W x 36mm D)

Weight 3 oz (0.2 lb, 90g)
Operating environment Indoors
Operating temperature range 32-104°F (0-40°C)
Operating humidity range 0-90% relative humidity
Storage temperature range -4-158°F (-20-70°C)
Battery One (1) AA lithium battery included
Voltage 1.5VDC
Retains all settings without power Yes, saved in non-volatile EEPROM
Mean battery life 10 years
Certifications FCC, IC Canada

Related Products

Questions & Phone Orders

1744 Willamette Street
Eugene, Oregon 97401
Call us: 1.877.584.6898

Shop with Confidence

Fast shipping, unbeatable customer service & 100% secure payment processing.

30-Day Satisfaction Guarantee

We're certain you'll love your gear, but if for some reason you don't like it just send it back.